Analisis Kebutuhan Alat Support Jalan Angkut Batubara Sektor 4 Menuju Coal Processing Plant Baru Pt. Asmin Bara Bronang Provinsi Kalimantan Tengah
DOI:
https://doi.org/10.55606/jurritek.v5i2.9195Keywords:
CBR, Coal Mining, Hauling Road, Support Equipment, Traffic Density URCIAbstract
Coal hauling activities are an important part of mining operation because they affect production continuity, cycle time efficiency, and operational safety. This study aims to analyze the requirements of road support equipment on the coal hauling road from Sector 4 to the new Coal Processing Plant (CPP) at PT. Asmin Bara Bronang, Central Kalimantan. Based on road geometry, traffic density, California Bearing Ratio (CBR), and Unsurfaced Road Condition Index (URCI). The research method used was applied research with a quantitative approach. Primary data ware collected through field measurements consisting of road geometri observations, traffic density observations, Dynamic Cone Penetrometer (DCP) testing to obtain CBR values, and road surface condition assessment using the URCI method. Secondary data were obtained from the company records. The results showed that the hauling road has a total length of 9.1 km with an average width of 16 m, and grade values ranging from -7.68% to 10.52%, which are still below the maximum standard of 12%. Traffic density reached 184 dump trucks/day, for coal hauling and 62 units/day for construction material transportation, indicating high traffic intensity. CBR values ranged from 7% to 100%, showing variations in subgrade bearing capacity. The URCI value ranged from 72,50 to 91.00, indicating fair to good road conditions. Based on the analysis of road conditions and maintenance area requirements, the recommended support equipment for maintaining the hauling road consists of 1 motor grader unit, 1 compactor unit, 1 bulldozer unit, and 1 water truck unit.
Downloads
References
Abdullah, M. H. (2021). Analisis daya dukung tanah terhadap kerusakan jalan di Desa Bulutigo Kecamatan Laren Kabupaten Lamongan [Skripsi, Universitas Islam Lamongan]. https://doi.org/10.30736/jt.v13i2.616
Halimatussa'diah, N., Razak, S., & Budiono, A. (2023). Analisis unsurfaced road condition index untuk kualitas jalan tambang PT Antareja Mahada Makmur Kalimantan Timur. Journal of Engineering Science and Technology Applications, 1(2), 34–45. https://doi.org/10.58227/jesta.v1i2.181
Lalamentik, L. (2020). Evaluasi geometrik jalan pada ruas Jalan Trans Sulawesi Manado–Gorontalo di Desa Botumoputi sepanjang 3 km.
Martono, N. (2010). Metode penelitian kuantitatif: Analisis isi dan analisis data sekunder. Rajawali Pers.
Muhammad, Y. (2024). Peningkatan travel speed pengangkutan overburden melalui perbaikan nilai URCI (Unsurfaced Road Condition Index) PT Putra Perkasa Abadi job site PT Adaro Indonesia Kalimantan Selatan [Skripsi, Universitas Muhammadiyah Mataram].
Mustofa, A., Wicaksono, J. G., Nurhakim, N., Afriko, A., & Melati, S. (2019). Perbaikan jalan angkut tambang: Pengaruh perubahan struktur lapis jalan terhadap produktivitas alat angkut. Jurnal Himasapta, 1(1). https://doi.org/10.20527/jhs.v1i01.906
Novela, I. (2025). Analisis kelebihan muatan (overloading) angkutan barang terhadap kerusakan dan keselamatan jalan [Skripsi, Universitas Atma Jaya Yogyakarta].
Novriadi, R. (2023). Analisa penilaian kondisi jalan menggunakan metode international roughness index (IRI) di ruas Jalan Lingkar Barat V [Skripsi, Universitas Batanghari Jambi].
Pangestu, M. B. (2026). Pengaruh perubahan kondisi jalan terhadap kinerja ruas Jalan Ahmad Yani (Kesawan) Kota Medan [Skripsi, Fakultas Teknik, Universitas Islam Sumatera Utara].
Sidiq, M. F. F., & Fauziah, M. (2025). Evaluasi pengaruh tingkat kerusakan perkerasan jalan tanpa lapisan menggunakan metode URCI terhadap travel speed dan volume coal hauling (tonnage) pada jalan hauling tambang STA 09+000–29+000.
Silaban, C. G., Andini, D. E., & Harsiga, E. (2025). Kajian kelayakan jalan angkut menggunakan metode AASHTO, unsurfaced road condition index, dan California bearing ratio di PT Mandala Karya Prima, Kalimantan Utara. Mineral, 10(1), 26–33. https://doi.org/10.33019/93fsva56
Sulfiana, S. (2025). Manajemen pemeliharaan pekerjaan jalan aspal pada proyek Jalan Kalukku Kabupaten Mamuju [Skripsi, Universitas Sulawesi Barat].
Sulung, U., & Muspawi, M. (2024). Memahami sumber data penelitian: Primer, sekunder, dan tersier. Edu Research, 5(3), 110–116.
Suryani, I. (2025). Evaluasi geometri jalan hauling Blok B4-Eto 1 pada PT Bapan Jaya Perkasa, Kecamatan Pomalaa, Kolaka, Sulawesi Tenggara. Jurnal Teknik AMATA, 6(1), 61–67. https://doi.org/10.55334/jtam.v6i1.335
Wahnadi, R., Al Gifari, J., Bakti, D. I., Rahmaddian, R., & Sakti, N. S. P. U. (2024). Pengembangan alat muat efektif untuk meningkatkan efisiensi kerja di area crusher PT Anugerah Bara Kaltim. Natural Resources and Environmental Management, 2(2).
Wicaksana, P. D. (2020). Pengaruh perbaikan rolling resistance pada jalan angkut terhadap estimasi biaya produksi andesit dengan simulasi menggunakan aplikasi TALPAC 10.2 di PT Lotus SG Lestari [Skripsi, Universitas Islam Negeri Syarif Hidayatullah Jakarta]. https://doi.org/10.15408/jipl.v1i1.20627
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Widya Lestari, Hepriyandi Luwyk Djanas Usup, Yustinus Hendra Wiryanto, Novalisae Novalisae, I Putu Putrawianta
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
_001.jpg)
